Commercial · Albuquerque, NM
For commercial coatings, epoxy floor prep is the make-or-break step, and it starts with the right grinding and shot blasting profile, not a quick acid wash. Elite Epoxy Albuquerque has served Albuquerque since 2016, prepping concrete slabs for epoxy, urethane cement, and polyaspartic systems in warehouses, shops, and facilities that cannot afford coating failure.
Proper prep begins with evaluating the slab and the coating system requirements, then building a clean, sound, open concrete surface. We remove sealers, curing compounds, laitance, glue, paint, rubber transfer, and weak concrete using planetary diamond grinders with HEPA dust control, or shot blasting when you need aggressive texture fast. Joints and cracks are routed and repaired with epoxy crack filler or polyurea, spalls are patched with polymer-modified repair mortar, and low areas are skimmed as needed. Our goal is the correct Concrete Surface Profile (CSP), typically CSP 2-3 for epoxy primers and decorative systems, and CSP 4-6 for heavier-build industrial coatings and urethane cement.
Albuquerque’s dry climate and wide temperature swings can hide moisture issues until the coating is down, so we check the slab before we build the system. When needed, we perform in-slab relative humidity testing (ASTM F2170) and pH checks, then recommend a moisture-mitigating epoxy primer if results call for it. Prep also addresses surface contaminants common in commercial spaces, including oils, coolants, and tire plasticizers, with targeted degreasing and mechanical removal instead of relying on solvents alone. Once the profile is right, we vacuum thoroughly, edge-grind tight areas, and detail corners so the primer wets out evenly and bonds where failures usually start.
Businesses choose us because we prep to spec and communicate clearly about what the floor needs, what it will look like, and how long it will take. You get a written scope that defines the prep method (grind, shot blast, or both), target CSP, joint plan, and any moisture mitigation so there are no surprises mid-project. Our crews use commercial-grade grinders, scarifiers when appropriate, and shot blasters with dust collection to keep active sites cleaner and reduce downtime. We plan around operating hours, loading zones, and safety requirements, with clear barricading and cleanup standards for occupied facilities.
Expect a straightforward walkthrough before work starts and a final inspection before coating, with photos available for documentation. We confirm substrate soundness, profile, repairs, and cleanliness, then lay out the coating sequence so your GC or facility team knows what comes next. You receive a free written estimate, a defined schedule, and prep that supports long-term adhesion for epoxy, polyaspartic, and urethane cement floors. If you are seeing peeling, fisheyes, bubbling, or recurring delamination, we can diagnose the failure, remove the weak coating, and reset the slab the right way with professional epoxy floor prep.
Yes. We operate as a professional epoxy contractor and carry insurance, and we provide written estimates and a defined scope before work begins.
We typically diamond-grind for a consistent mechanical profile and stronger adhesion. Acid etching alone is not a substitute for proper surface profiling on most slabs.
Sometimes. We test adhesion and check for peeling, contamination, and incompatible coatings, then grind and recoat if the base is sound. If the old coating is failing, removal and a new system is the reliable option.
A UV-stable topcoat, commonly polyaspartic or aliphatic polyurethane, helps reduce ambering and chalking compared to epoxy exposed to direct sun.
Yes. We install vinyl flake broadcast systems in a range of blends and coverage levels, then lock it in with a clear topcoat in gloss or satin.
Epoxy floor prep is the foundation of every successful commercial coating install. If the concrete is too smooth, contaminated, or weak at the surface, even premium epoxy will delaminate. Elite Epoxy Albuquerque provides professional grinding and shot blasting to create the right Concrete Surface Profile (CSP), repair defects, and prep slabs for epoxy, polyaspartic, and urethane cement systems in commercial and industrial spaces.
Mechanical prep beats shortcuts. Acid etching rarely removes sealers, adhesives, or dense trowel burn, and it cannot reliably produce a measurable profile across a working floor. Grinding and shot blasting physically remove weak laitance and contamination, then open the concrete pores so primers can wet out and bite. We select tooling and blast media based on slab hardness, existing coatings, and the performance needs of the finished system, from thin-mil epoxy to high-build industrial broadcast floors.
Good epoxy floor prep also means addressing what causes failures at the edges and joints. We detail perimeter areas with edge grinders, clean and rebuild control joints when required, and route and fill cracks so they do not telegraph through the coating. For facilities with oils, tire marks, or chemical exposure, we incorporate degreasing and aggressive mechanical removal so contaminants are not pushed deeper into the slab.
If you need commercial epoxy floor prep in Albuquerque, we will walk the site, identify risks, and provide a free written estimate with the right prep method for your coating goals and timeline. The result is a slab that is clean, profiled, repaired, and ready for a coating that bonds and stays down.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in Albuquerque. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.
